How to adjust the Bespoke fridge's door height

Is one of the doors on your 4-Door BESPOKE fridge hanging a little low? Adjusting the leveling legs and the height of the doors will solve this problem, so everything will look nice and even. You won’t need an installer to get the job done – just a flat-head screwdriver and some snap rings.

How to adjust the Bespoke fridge's door height

Note

These are the most common steps, but for instructions that are specific to the model of your fridge, see your user manual. If you don't have your user manual, you can download a copy from our website at any time.

Adjust the top doors

Important

The lever will not turn past the maximum limit. It may make a noise if it is turned too far. Do not raise the doors excessively high because this may interfere with the upper hinge cover of the fridge door or damage the top cover.

After leveling the fridge, you may notice that the upper left and right doors aren't aligned with each other. Rather than mess with the leveling of the whole fridge, you can just adjust one or both upper doors until they align properly. Follow the steps below and check out our video on how to adjust the top edge door alignment.

Four-door models

Open the right-side door of the freezer. Keep the other freezer door and both fridge doors closed. Locate the height lever on the bottom of the right-side door.
Note: We recommend keeping items in the door bins during the alignment process. Leaving the bins empty could affect the doors' alignment later on.
Turn the height lever toward UP to raise the right-side door, or turn it toward DOWN to lower the door. To make alignment easier, you can lift the fridge door slightly while adjusting.
If the doors are still not aligned but you cannot adjust the height lever any further, try using the snap rings.
Note: You should only use the snap rings if you cannot align the doors with the height lever.
The snap rings come in 4 different sizes: 1 mm, 1.5 mm, 2 mm, and 2.5 mm. Check the height difference between the doors, and then choose the snap ring that you think will correct the height difference.
Note: Insert only one snap ring per door. If you insert two or more snap rings, the rings may slip out or make a rubbing noise.
Once you've chosen your desired snap ring, lift up and hold the door with the lower height.
Insert a suitably sized snap ring between the door grommet.
If needed, repeat these steps to adjust the height of the other top-side door.

Three-door models

Check the height difference between the doors, and then lift up and hold the door with the lower height.
Insert a suitable-sized snap ring between the door grommet and the hinge.

Read less

Adjust the bottom doors

Note

We recommend keeping items in the door bins during the alignment process. Leaving the bins empty could affect the doors' alignment later on.

You can adjust the height of the bottom freezer doors if they appear uneven. Before adjusting the doors, make sure the refrigerator is level. Check out the video in the first section for additional information.

Open the door you’d like to adjust, and then lift it slightly.
Next, locate the height lever at the bottom of the door.
The height lever includes a grommet that can be moved inward or outward to adjust the door height by 1 mm.
Turn the grommet in your desired direction to raise or lower the door. If you need to increase the door’s height, turn the grommet outward. To decrease the door’s height, turn the grommet inward.
If needed, repeat these steps to adjust the other bottom door.

Read less

Adjust the doors on side by side models

The height of your side-by-side Bespoke refrigerator doors can be adjusted via the clamp and height nuts on the front bottom of the door. Follow these steps.

Open the door you want to adjust.
Locate the two nuts on the front bottom of the door.
Using a 19mm spanner, turn the clamp nut clockwise to loosen, and then open the door.
Inside the door, turn the height nut counter clockwise to raise it or clockwise to lower it.
When finished, tighten the clamp nut by turning counter clockwise.

Read less

Adjust the panels

Did you know the panels on your BESPOKE 4-Door Flex model can be customized and swapped out for other colors? See our guide to learn about the options available to you.

Read less

Recommended Articles

How to adjust the BESPOKE fridge's door height

Adjust the top doors Important: The lever will not turn past the maximum limit. It may make a noise if it is turned too far. Do not raise the doors excessively high because this may interfere with the upper hinge cover of the fridge door or damage the top cover. After leveling the fridge, you may notice that the upper left and right doors aren't al

Samsung refrigerator shelf/drawer removal and cleaning guide

Samsung refrigerator shelf/drawer removal and cleaning guide Sometimes messes in the fridge require deeper cleaning and, to get the job done, you have to remove the refrigerator bins, shelves, and drawers. Most of them are made for easy removal, but knowing the right way to remove them makes it even easier. Once they're out, you can really begin cl

Samsung refrigerator shelf/drawer removal and cleaning guide

Door bins, shelves, and crisper drawers No matter what kind of fridge you have, its door bins, shelves, and crisper drawers can be removed. Door bins: The top door bin section has a marked line to make removing and reinserting bins easier. To remove a bin, push the bin up with both hands, and then pull it out from the door. To reinsert the bin, sim

Previous Next

Table of contents

We're here for you

Contact Samsung Support

Contact us online through chat and get support from an expert on your computer, mobile device or tablet. Support is also available on your mobile device through the Samsung Members App.

Get support